How to install timber skirting boards
Installing timber skirting boards provides the critical junction between your wall linings and flooring, concealing expansion gaps while protecting your plasterboard from impact. While seemingly straightforward, achieving tight, trade-quality internal and external joints requires methodical measurin
Quick answer
To install timber skirting boards, locate wall framing studs, scribe internal corners with a coping saw, and cut external corners at 45-degree mitres. Fasten profiles using 50mm 16-gauge brad nails into studs combined with continuous beads of polyurethane construction adhesive to prevent cupping and joint separation.
- Skill level
- Intermediate
- Time
- 1–2 days (based on an average 3-bedroom home)
- Trade
- Carpentry & Joinery
- Updated
- 17 November 2026
Tools you will need
- Dual
- Coping saw
- Heavy
- 8m tape measure
- Electronic multi
- Combination square or digital angle finder
- Pencil
🪚 How to Install Timber Skirting Boards: The Complete Trade Guide
What is the correct method to install timber skirting boards?
Installing timber skirting boards provides the critical junction between your wall linings and flooring, concealing expansion gaps while protecting your plasterboard from impact. While seemingly straightforward, achieving tight, trade-quality internal and external joints requires methodical measuring, correct timber selection, and precise cutting techniques. This guide outlines the standard Australian second-fix carpentry method to deliver seamless, durable baseboards throughout your home.
What skill level and time are required to install skirting boards?
Intermediate — Estimated time: 1–2 days (based on an average 3-bedroom home)
What tools do you need to cut and install timber skirting boards?
Dual-bevel compound mitre saw (minimum 254mm blade, 60T or higher negative-rake timber finishing blade) 16-gauge (16Ga) pneumatic or cordless finish nailer (firing 50mm to 63mm C-series brad nails) Coping saw (with flexible fine-tooth timber blades) Heavy-duty caulking gun (minimum 12:1 thrust ratio for structural adhesives) 8m tape measure (high-contrast, minimum 27mm wide blade for standout) Electronic multi-scanner/stud finder (deep-scan timber and live AC detection) Combination square or digital angle finder Pencil (hard carpenter’s pencil, 2H or 4H for razor-thin cut lines)What materials and fixings are required for timber skirting boards?
🪵 Skirting profiles: Standard profiles such as 67x18mm or 90x18mm (Colonial, Torus, or Lambs Tongue) or 90x18mm / 140x18mm Single Pencil Round (MDF pre-primed for painted finish, or Finger-Jointed Pine / Solid Tasmanian Oak for clear finishing). Factor in a 15% wastage allowance for mitres and offcuts. 🪵 Fixings: 50mm or 63mm 16Ga galvanised brad nails. 🪵 Adhesive: High-grab polyurethane construction adhesive (e.g., Sikaflex-11FC or Bostik Heavy Duty). 🪵 Filler: Flexible acrylic gap sealant (e.g., Selleys No More Gaps Interior) and trade-grade timber putty. 🪵 Abrasives: 120-grit and 240-grit aluminium oxide sandpaper sheets.Safety Requirements
⚠️ Eye and ear protection: Safety glasses compliant with AS/NZS 1337.1 and Class 4 or 5 hearing protection compliant with AS/NZS 1270 when operating power saws and nail guns. ⚠️ Respiratory protection: A fitted P2 respirator compliant with AS/NZS 1716 is mandatory when cutting Medium Density Fibreboard (MDF) to prevent the inhalation of hazardous softwood dust and synthetic resins. ⚠️ Services isolation: Always isolate or thoroughly map wall cavities with an electrical scanner before fixing into framing to avoid puncturing concealed 240V wiring or plumbing runs, complying with AS/NZS 3000 safe working practices. ⚠️ Fastener safety: Treat all pneumatic and cordless nail guns with primary care; keep hands a minimum of 200mm away from the discharge nosepiece, and never disable the contact-actuation safety tip.Step-by-Step Guide
Step 1: Wall Preparation and Stud Mapping
1️⃣ Surface clearing and stud location: Scrape down the lower edge of the plasterboard using a broad knife to remove rogue plaster lumps, adhesive dabs, or framing protrusions. Using an electronic stud finder, map your vertical timber wall studs (typically spaced at 450mm or 600mm centres in accordance with AS 1684). Mark each stud location on the subfloor with a pencil, or make a light pencil mark on the plasterboard at roughly 150mm above the floor so it remains visible once the skirting board is rested in place.
Step 2: Establish the Room Sequence and Scribing First Runs
2️⃣ Sequence of installation: Plan to install the longest uninterrupted run first. For straight, wall-to-wall internal junctions, cut your first board squarely at 90 degrees on both ends to fit tightly wall-to-wall.
💡 For pristine internal corners on profiled timbers, do not use 45-degree flat mitres; standard Australian trade practice dictates a scribed joint (also called a coped joint). The baseboard running into the corner is cut square, while the intersecting board is cut at an inside 45-degree bevel, exposing the profile edge which is then hand-cut using a coping saw back-angled slightly (2 to 5 degrees negative rake). This scribe seamlessly overlaps the face of the first board and will not open up as framing timber naturally expands and shrinks.
Step 3: Cutting and Joining on Long Straight Runs (Scarf Joints)
3️⃣ Mitred lap/scarf joints: If a wall length exceeds the length of a single timber length (typically 5.4m stock lengths), join two lengths together over a wall stud using a 45-degree scarf joint rather than a butt joint.
Cut the trailing piece at a 45-degree angle facing outward. Cut the leading piece at an opposing 45-degree angle facing inward. Position this overlapping joint directly over a wall stud, apply PVA or timber glue between the timber faces, and nail through both profiles into the timber stud for an invisible, movement-resistant joint.Step 4: Cutting External Corners
4️⃣ Bisecting external angles: External corners are rarely a precise 90 degrees. Use a digital bevel gauge or combination square to measure the true corner angle.
Bisect the angle evenly between both pieces (e.g., if the corner reads 91 degrees, adjust your mitre saw to precisely 45.5 degrees). Cut your first board slightly over length, align the heel of the mitre against the corner, and mark the exact cut point on the back of the timber. Test-fit both mitred sections dry before fixing.Step 5: Fixing the Skirting Boards
5️⃣ Adhesive and mechanical fastening: Apply continuous serpentine beads of construction adhesive along the back of the skirting board, ensuring you stay roughly 20mm clear of the edges to avoid squeeze-out.
Firmly press the timber against the plasterboard. Fire two 16Ga brad nails into every wall stud: one positioned approximately 25mm down from the top edge, and one 25mm up from the bottom edge into the wall bottom plate (90x45mm or 70x45mm base rail). Nails must penetrate the structural framing timber by at least 30mm.Step 6: Punching, Filling, and Finishing
6️⃣ Surface detailing: Ensure all brad nail heads sit counter-sunk 1.5mm to 2mm below the timber face.
Fill all nail indentations using an appropriate trade timber filler, slightly mounding the filler to allow for minor cure shrinkage. Apply a fine bead of flexible acrylic gap sealant along the top junction between the skirting board and the plasterboard, smoothing it off with a damp profile tool or sponge. Once dried, sand all filled nail holes flush using 240-grit sandpaper in preparation for undercoat and finishing paint.Common Mistakes to Avoid
Pro Tips
💡 Back-bevel your copes: When removing the profile waste with your coping saw, undercut the cut-line at an angle of roughly 5 degrees backwards. This ensures only the front finished face makes contact with the mating board, giving you a hairline fit every time without rear binding. 💡 Use offcut templates for marking: Cut a clean 150mm sample offcut of your skirting profile. You can slide this into corners to precisely trace your scribe cuts or to visually verify your bottom plate level before handling full 5.4m lengths. 💡 Prefinish boards prior to fixing: Apply your timber primer and the first finish coat of enamel while the timber lengths are flat on sawstools outside. Once cut and fixed, you only need to fill nail holes, caulk the perimeter, and apply one final seamless topcoat—saving hours on your knees cutting in with a brush.Recommended Tools
DeWalt DWS780-XE 305mm Compound Slide Mitre Saw: Highly accurate detent system and XPS shadow-line cut alignment, critical for cutting wide skirting profiles vertically or nested without blade deflection. (Note: Tool purchases over $300 may qualify for the Australian EOFY Instant Asset Write-Off for eligible trade businesses). Hikoki NT1865DBAL 18V Brushless 16Ga Finish Nailer: Completely eliminates the need for trailing air hoses and noisy compressors while driving 63mm brad nails consistently through seasoned structural framing timbers.Frequently asked questions
- What is involved in install timber skirting boards?
- Installing timber skirting boards provides the critical junction between your wall linings and flooring, concealing expansion gaps while protecting your plasterboard from impact. While seemingly straightforward, achieving tight, trade-quality internal and external joints requires methodical measurin
- What skill level do I need for install timber skirting boards?
- Intermediate — Estimated time: 1–2 days (based on an average 3-bedroom home)
- What are common mistakes when install timber skirting boards?
- 1. Relying on mitres for internal corners: Timber and plaster move continuously. Flat 45-degree internal mitres invariably pull apart, gap, or crush over seasonal temperature changes. Always use a coped/scribed joint on internal profiles. 2. Fastening exclusively into plasterboard: Pinning skirting solely into Gyprock using short nails will inevitably result in boards bowing off the wall
- What tools do I need for install timber skirting boards?
- This guide includes a comprehensive tools list. Key carpentry & joinery tools are detailed in the Tools Required section.
- What is the Australian standard for installing skirting boards?
- Timber skirting installation in residential builds is governed by AS 1684.2 for timber framing fixings and the National Construction Code (NCC). Fixings must penetrate timber wall studs or the bottom plate by a minimum of 25mm to 30mm. In cyclonic or high-movement regions, additional flexible polyurethane adhesive behind the profile is required by standard building tolerances.
- Should internal skirting board corners be mitred or scribed?
- Internal skirting joints should always be scribed or coped, never mitred. Scribing involves cutting a 45-degree profile on one board and following the contoured face line with a coping saw. This allows the joint to remain visually tight and seamless when the adjacent timber expands or contracts across seasonal humidity cycles throughout Australia.
- What size nails should be used for fixing skirting boards?
- Use 50mm to 63mm 16-gauge (16Ga) finish brad nails driven through the profile and drywall into timber framework. Fasteners must anchor securely into the timber studs or bottom plate. Pinning solely into plasterboard lining fails over time, causing timber boards to warp, cup, or pull away from uneven walls.
- How much extra skirting board timber should you order for wastage?
- Trade practice in Australia requires adding a 10% to 15% allowance to total measured wall linear meterage. This surplus accommodates 45-degree external mitre cuts, scribed internal overlaps, scarf joints over extended wall lengths, and defect trimming on timber or moisture-resistant MDF stock.
Written by Chippy, the Carpentry & Joinery specialist at Aus.Tools.